TRAINING PNEUMATIC & HYDRAULIC SYSTEM
Daftar isi :
TRAINING PNEUMATIC & HYDRAULIC SYSTEM
TRAINING PNEUMATIC & HYDRAULIC SYSTEM
Overview Training Pneumatic & Hydraulic System
Sistem otomasi dunia industri berkembang pesat seiring semakin tingginya teknologi yang digunakan. Begitu pula dengan perangkat elektro pneumatic dan hydraulic yang digunakan dunia industri dan manufaktur. Sebagian besar industri mengimplementasikan sistem pneumatic dan hydraulic dalam instalasinya.
Melalui pelatihan ini para peserta diharapkan dapat meningkatkan pengetahuan dan wawasan mengenai nama, fungsi, simbol, cara kerja dan kemampuan masing-masing komponen pneumatic & hydraulic. Pelatihan ini akan memberikan pemahaman mengenai komponen-komponen dasar dan fungsi dari sistem hydraulic dan pneumatic. Topik yang akan dipelajari meliputi: standard symbols, pumps, motor system, control valves, control assemblies, actuators, FRL, maintenance procedures, and switching and control devices. Diharapkan peserta akan dapat memahami mengenai pengoperasian fluid power system, termasuk desain, aplikasi dan troubleshooting.
Tujuan :
- Mengetahui proses mekanisasi proses industri yang berkaitan dengan sistem pneumatic & hydraulic;
- Mengetahui teknik otomasi mesin;
- Mengetahui tentang penerapan sistem pneumatic & hydraulic di industri;
- Mengatahui dasar-dasar perancangan dan desain sistem pneumatic & hydraulic;
- Mengetahui elektro pneumatic & hydraulic;
- Memberikan pengetahuan tentang pengoperasian dan pemeliharaan sistem pneumatic & hydraulic beserta troubleshooting-nya.
Materi Training Pneumatic & Hydraulic System
- Introduction to Fluid Power
- What is Fluid Power
- Advantages of Fluid Power
- Applications of Fluid Power
- Components of Fluid Power Systems
- Power Transmitting Fluids
- Fluids: Oil and Air
- Pressure, Head, and Force
- The Perfect Gas Law
- The Continuity Equation
- Bernoulli’s Equation
- Pascal’s Law and Application
- Bulk Modulus
- Pressure Losses in Valve and Fitting
- Flow and Pressure Measurement
- Energy, Power, and Flow Rates
- Basic Fluid Power System
- The Basic Pneumatic System
- The Basic Hydraulic System
- Air Compressors
- Hydraulic Pump
- Pump Performance
- Pump Selection
- Pressure Intensifiers
- Motors and Actuators
- Hydraulic Motor Performance
- Low-Speed, High-Torque Motors
- The Distribution System
- Steel Pipes, Steel Tubing and Plastic Tubing
- Flexible Hoses
- Quick Disconnect Coupling
- Metric Steel Tubing
- Control Components and Simple Circuit
- Directional Control Valve
- Pressure and Flow Control Valve
- Servo Valve
- Hydraulic Fuses
- Pressure and Temperature Switches
- Shock Absorbers
- Hydraulic Circuit
- Control of a Single and Double-Acting Hydraulic Cylinder
- Regenerative Circuit
- Pump-Unloading Circuit
- Double-Pump Hydraulic System
- Pressure Intensifier Circuit
- Counterbalance Valve Application
- Hydraulic Cylinder Sequencing Circuit
- Automatic Cylinder Reciprocating System
- Locked Cylinder Using Pilot Check Valves
- Cylinder Synchronizing Circuit
- Metering in and Metering out Fail-Safe Circuits
- Speed Control of Hydraulic Motor
- Hydraulic Motor Breaking System
- Accumulators and Accumulator Circuit
- Pneumatic Circuit
- Fluid Conditioners
- Air Service Unit
- Air Pressure Losses in pipes
- Control with Orifice
- Air Control Valve
- Pneumatic Actuators
- Basic Pneumatic Circuit
- Circuit Design with Intuitive and Cascade Method
- Accumulator System Analysis
- Pneumatic Circuit Analysis
- Electrical Controls for Fluid Power Circuit
- Electrical Components
- Control of a Cylinder Using a Single Limit Switch
- Dual Cylinder Sequence Circuits
- Electrical Control of Regenerative Circuit
- Counting, Timing, and Reciprocation of Hydraulic Cylinder
- Programmable Logic Controllers (PLC)
- Fluid Power Maintenance and Safety
- Sealing Devices
- The Reservoir System
- Filters and Strainers
- Filtration and Contamination Assessment
- Beta Ratio of Filters
- Temperature Control
- Troubleshooting Fluid Power Circuit
- Safety Considerations
- General problems and solutions
Peserta Training Pneumatic & Hydraulic System
Para Foreman, Technician, Technical Assistance, Engineer, Mechanics, Supervisor, Inspection & Repair Managers, Operator, serta Tenaga lapangan yang menangani pneumatic & hydraulic power system.
Jadwal Pelatihan Lokal Media Training 2024 :
Batch 1 : 03 – 04 Januari 2024 | 16 – 17 Januari 2024 || Batch 2 : 06 – 07 Februari 2024 | 20 – 21 Februari 2024
Batch 3 : 05 – 06 Maret 2024 | 19 – 20 Maret 2024 || Batch 4 : 03 – 04 April 2024 | 23 – 24 April 2024
Batch 5 : 07 – 08 Mei 2024 | 21 – 22 Mei 2024 || Batch 6 : 05 – 06 Juni 2024 | 25 – 26 Juni 2024
Batch 7 : 09 – 10 Juli 2024 | 23 – 24 Juli 2024 || Batch 8 : 06 – 07 Agustus 2024 | 20 – 21 Agustus 2024
Batch 9 : 04 – 05 September 2024 | 18 – 19 September 2024 || Batch 10 : 08 – 09 Oktober 2024 | 22 – 23 Oktober 2024
Batch 11 : 06 – 07 November 2024 | 26 – 27 November 2024 || Batch 12 : 04 – 05 Desember 2024 | 18 – 19 Desember 2024
Jadwal Pelatihan Lokal Media
TEMPAT PELAKSANAAN PELATIHAN
- REGULER TRAINING
- YOGYAKARTA
- JAKARTA
- BANDUNG
- MALANG
- SURABAYA
- BALI
- LOMBOK – NTB
- IN HOUSE TRAINING
- ONLINE TRAINING VIA ZOOM
Note :
Waktu dan tempat pelaksanaan pelatihan bisa kami sesuaikan dengan kebutuhan peserta.
Investasi Pelatihan Lokal Media Training:
- Investasipelatihan selama tiga hari tersebut menyesuaikan dengan jumlah peserta
- Apabila perusahaan membutuhkan paket in house training, anggaran investasi pelatihan dapat menyesuaikan dengan anggaran perusahaan.
Fasilitas Pelatihan di Lokal Media Training:
- Hotel
- Tempat Pelatihan
- Module / Handout
- FREE Flashdisk
- Sertifikat
- FREE Bag or bagpackers (Tas Training)
- Training Kit (Dokumentasi photo, Blocknote, ATK, etc)
- 2xCoffe Break & 1 Lunch, Dinner
- FREE Souvenir Exclusive
- Training room full AC and Multimedia
